PU Injection Grouting in Chennai

Quick answer:

PU injection grouting stops active water leaks in concrete. Polyurethane resin is pumped under pressure into the crack or joint through small drilled ports. The resin reacts with the incoming water, expands, and seals the full depth of the leak path. It is the standard repair for leaking basements, lift pits, sumps and construction joints.

Book Your Expert Site Visit

Share your requirement and our waterproofing specialists will inspect the site and send you a tailored quotation.

Your information is safe and will not be shared.

Established 2016

A highly experienced applicator delivering superior quality compared to major brands.

Genuine Warranty

Warranty for Product + Service
promise to repair or replace a defective product or service at no extra cost.

Brands we used

SikaFosroc
Dr. FixitMYK Arment
PenetronArdex Endura
MAPEIMC-Bauchemie
CICOCCI
Dr. FixitMYK Arment
Local conditions

Why it is in demand in Chennai

Large parts of the city are built on low, formerly marshy ground. In Velachery, Pallikaranai, Madipakkam and Mudichur, and along much of the OMR, the water table is high all year and rises further during the northeast monsoon. Any structure below ground level, such as a basement car park, lift pit, underground sump or retaining wall, then sits in water for months.

Under that pressure, ground water finds every crack, every construction joint and every pipe sleeve. Surface patching with cement fails because the water simply pushes it off. PU injection works the other way round: it uses the water already in the crack to trigger the seal, so it can be done while the leak is running. That is why it is the first response for flooded basements and lift pits after heavy rain.

Signs you need PU injection

  1. Water dripping or flowing through a visible crack
  2. Basement walls or floors that weep after rain
  3. Water collecting in the lift pit
  4. Leaks at the joint between wall and floor slab
  5. Seepage around pipes passing through concrete
  6. Ceiling leaks in a podium or car park below a garden or driveway
  7. Expansion joints dripping onto parked vehicles
Root cause

What is actually going wrong

Construction joints are open.

 Concrete is poured in stages. Where a new pour meets hardened concrete, the bond is weak unless a waterstop was fitted properly. These joints are the most common leak path in basements.

Failed external membrane.

Basements and lift pits are meant to be wrapped in a membrane on the soil side during construction. If that membrane is torn during backfilling, poorly lapped, or left out, ground water reaches the concrete directly. The outside cannot be reached once the building is up, so the leak is sealed from the inside by injection.

Shrinkage and settlement cracks.

Concrete shrinks as it cures, and buildings settle. The resulting cracks may be hair-thin but run through the full wall thickness.

Honeycombed concrete.

Poorly compacted concrete has voids that link up into channels.

In every case, water under pressure is travelling through a defined path. Injection fills that path through its full depth, and that is what makes the repair hold.

Recommended systems

SystemWhere we use itNotes
Hydrophobic PU foam resinRunning or gushing leaksExpands many times on contact with water and stops flow in minutes
Flexible PU gel or elastomeric resinSecond-stage permanent sealStays flexible and tolerates crack movement
Hydrophilic PU resinFine, damp cracksSwells with moisture for a tight seal
Steel or aluminium injection packersAll injectionsRemoved after the resin cures
Polymer repair mortarSurface finishingCloses drill holes and the crack face

For heavy leaks we use two stages: foam to stop the water, then flexible resin to make the seal permanent.

Our process

How we do the work

  1. Trace the leak.We follow the water back to the crack or joint and mark its full length.
  2. Drill.  Holes are drilled at a 45 degree angle on alternating sides of the crack, to meet it at mid-depth. Spacing is usually 200 to 300 mm.
  3. Fix packers. Injection packers are set and tightened in each hole.
  4. Flush. Clean water is injected where required, to clear the crack and wet the surface for the resin.
  5. Inject.Resin is pumped from the lowest packer upwards, until it shows at the next packer or along the crack face..
  6. Second pass.Flexible resin is injected for permanent sealing where specified.
  7. Cure and check.The area is watched until the leak has stopped fully.
  8. Finish. Packers are removed, holes filled and the surface made good.

A typical crack of a few metres is completed within a day. The space stays usable throughout.

What decides your quote

For PU injection, the factors are the length of the cracks and joints, the number of injection points, the rate of water flow, and access to the area.

Frequently asked questions

1

Can it be done while water is flowing?

Yes. PU resin needs water to react, so active leaks are exactly where it works best.

2

Is PU injection grouting a waterproofing method on its own?

It is a leak-sealing method. It fixes the cracks and joints where water enters. Where the whole surface is porous, it is combined with a coating or with pressure grouting.

3

How long does the repair last?

A properly injected crack stays sealed for many years. Flexible resin copes with the small movements that reopen rigid repairs.

4

Do you provide injection grouting near me?

We carry out PU injection across Chennai, including basements and lift pits in apartment complexes and commercial buildings. Send us a short video of the leak for a first opinion.

5

What is the difference between PU and epoxy injection?

PU is flexible and stops water. Epoxy is rigid and restores strength in dry structural cracks. Some repairs need both.

6

Will you have to break the wall or floor?

No. The work involves only small drilled holes, which are filled afterwards.

7

Is it safe inside an occupied building?

Yes. The work is low in noise and dust, and the cured resin is inert.

8

My lift pit floods every monsoon. Can this fix it?

In most cases, yes. We inject the joints and cracks, then coat the pit with a crystalline system.

9

Is there a warranty?

Yes. A written warranty covers the treated cracks and joints.

Stop the leak today

Call or WhatsApp WATREX with a short video of the leak. We attend urgent basement and lift pit leaks across Chennai.

PU, epoxy or pressure grouting: which one do you need?

MethodUse it whenWhat it doesDoes not do
PU injection groutingWater is actively leaking through a crack or jointExpands on contact with water and seals the leak path; stays flexibleRestore structural strength
Epoxy injection groutingA dry structural crack runs through a beam, column or slabBonds the concrete back together and restores load capacityWork in wet or moving cracks
Cementitious pressure groutingConcrete is porous or honeycombed over a wide area, with no single crackFills hidden voids through a grid of nozzlesSeal fine cracks or stop running water